Lambro 200
-
Lambro 200
Lambro 200.
Technical Specification
| Model | Lambro 200 |
| Production Started | June 1963 |
| Production Ended | July 1965 |
| Frame Prefix | M42 |
| Engine Prefix | FLI200 |
| Starting Frame N° | 300001 |
| Starting Engine N° | 300001 |
| Amount Produced | 18,260 |
| Engine | 198cc, two stroke, 66x58mm, Inside cab |
| Power & Rate | 8.9HP at 5,000RPM |
| Compression Ratio | 1:7 |
| Head & Cylinder | Aluminium & Cast Iron |
| Engine Cooling | Forced Air |
| Crankcase Oil | HD SAE 50 1600grams |
| Starter | Kickstart or Electric |
| Clutch | Multiple discs in oil bath |
| Gears | 4 speed hand shifter and reverse |
| Gear Ratios | 1st 1:36.2 |
| 2nd 1:18.7 | |
| 3rd 1:11.7 | |
| 4th 1:7.9 | |
| Reverse 1:38.7 | |
| Ignition | Magneto |
| Spark Advance | 18°-20° 2.34-1.94mm before TDC (top dead centre) mark on the flywheel |
| Point Settings | .35-.45mm |
| Sparkplug | Bosch 225-240, long thread |
| Primary | Gear |
| Secondary | Shaft and differential |
| Transmission Oil | SAE 90 320grams |
| Carburetor | dell'orto SH1/18 |
| Carburation | Main 97, Pilot 45, valve 1 |
| Fuel Mix | 4.00% |
| Fuel Consumption | 1lt per 32km |
| Fuel Capacity | 11.5lts |
| Range | 275km |
| Maximum Speed | 58-61km/h |
| Brake Type | Front: Mechanically controlled drum |
| Rear: Hydraulically controlled drum | |
| Tire | 4.00 x 10 T |
| Tire Pressure | Front: 2.50ATM |
| Rear: 3.25ATM | |
| Front | Oscillating connecting rods with hydraulic shock absorber |
| Rear | Rigid cross beam with longitudinal leaf springs |
| Dry Weight | 348kg open trunk, 373kg closed compartment |
| Longitudinal Dimension | 2,910mm |
| Transversal Dimension | 1,345mm |
| Vertical Dimension Box | 1,670mm |
| Max Hight | 1,670mm |
| Ground Clearance | 120mm |
| Wheel Base | 1,710mm |
| Track Width | 1,180mm |
| Minimum Turning Radius | 2,605mm |
| Load Capacity | 475-500kg |
| System | 6 Volt with 18amp battery, 6 volt with 25amp battery for Electric Starter. |
| Frame | |
| Cab | Round cab with single headlight & canvas back |
| Floor mats as standard. | |
| Doors | |
| Optional Extras | |
| Trunk Type | |
| Colours | Grey, Blue, Green |
| Frame | Steel tubing with 1,900mm resistence, Stamped metal floor pan |
| Cab | Round cab with single round headlight & canvas half back |
| Floor mats as standard. | |
| Doors | Optional conventional doors |
| Trunk Type | Aluminum compartment |
| Aluminium pressed pickup trunk with hinged rear panel | |
| Also available as chassis only | |
| Colours | Grey, Blue |
| Optional Extras | Speedometer, Clock, Electric windshield wiper |
| Steering | Handlebar |
| Accelerator | Actuated by twisting of the right handle bar grip |
| Brakes | Front: Foot pedal |
| Rear: Right lever on handlebar | |
| Clutch | Left lever on handlebar |
| Gears | Actuated by twisting of the left handlebar grip with clutch engaged |
| Reverse by actuating lever on the centre column whilst not in motion with | |
| clutch engaged and first gear selected |
Copyright © 2018-2025 - All Rights Reserved - British lambretta Archive
Design by John Walklate